Symmetricom S100 Manual do Utilizador Página 122
- Página / 166
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
114 S100 User Guide – Rev. D – June 2005
SyncServer S100
How to install NTP v4 on a UNIX system
Requirements: A Unix system with compiler, standard tools and openssl installed.
1. Download NTP tarball from
www.ntp.org
2. Extract the source using tar -xvf <ntp tarball>
3. Run the configuration and specify autokey using
./configure --with-
crypto=autokey
4. Run make.
5. Make install.
How to configure an NTP v4 client to connect to an NTP v4 server with the autokey scheme
1. Create or modify /etc/ntp.conf and add a server line using vi (server <ipaddress>
autokey)
2. Run
ntpd and verify proper operation.
How to verify NTP v4 autokey client connectivity with an NTP v4 server
To confirm that a secure NTP v4 session with autokey has been established with a server, do
one of the following :
1.
ntpdc command showpeer <server ip> and look for the auth flag
2.
ntpq command associations and look for auth category (ok)
3. Run ntpd -ddd and watch output for crypto statements and packet sizes
How to install your S100
All information about this is covered in “Installing Your S100” on page 19.
How to get time using dial-up
See “Dialup Settings dialog” on page 38 for details about this.
How to get time using GPS
See “GPS” on page 35.
- Chapter 1 1
- S100 User Guide 1
- Table of Contents 3
- Chapter 4 4
- The Web-Based Interface 53 4
- Chapter 5 6
- Chapter 6 6
- Appendix A 7
- S100 Specifications 119 7
- Introduction and Overview 9
- Conventions Used 10
- Time Standards 11
- Product Details 11
- Stratum Levels 12
- Special Safety Instructions 14
- S100 Technology 15
- Web-based Access 16
- Time Distribution Model 17
- How the S100 Works 17
- S100 and Time Distribution 18
- S100 and Client Software 18
- Chapter 3 21
- Overview 21
- Getting Up and Running 21
- Unpacking Your S100 21
- Your CD-ROM 23
- Using the Software 24
- PuTTY Folder Details 24
- PUTTY.EXE 24
- PSCP.EXE 24
- PSFTP.EXE 25
- PLINK.EXE 25
- PAGE ANT. EXE 25
- PUTTYGEN.EXE 26
- Installing Your S100 27
- Rack Mounting 27
- Primary Power Connection 27
- Setting Up the Hardware 29
- On the S100 Rear Panel 30
- Installing the GPS Antenna 31
- Installing the GPS antenna 32
- Setting Up the IP Address 34
- Testing Network Functionality 36
- Turning Off Your S100 37
- How to Acquire Time 38
- Administrator Log-In 39
- The Configuration Wizard 40
- Choose Your Time Source 41
- Figure 3-18: Dialup Backup 43
- Figure 3-19: Dial-up Settings 43
- Figure 3-24: Dial-up Settings 47
- Configuring NTP 53
- IRIG-B (v.120,122,123) 53
- Figure 3-34: Dial-up Settings 54
- Using SymmTime™ 57
- To Synchronize SymmTime: 59
- The Web-Based Interface 61
- Logging In 62
- Administrative Interface 62
- Admin Interface: Base Menu 63
- Administrative Menu: Expanded 64
- System Status 65
- Timing Configuration 65
- NTP Relationships 66
- NTP Time Source Test 68
- NTP Dialup 68
- NTP Restart 69
- NTP Status 69
- Advanced: ntp.conf 71
- Advanced: Keys/Certificates 72
- Timing Engine 73
- Timecode Settings 74
- GPS Information 75
- GPS Signal Strength 76
- GPS Time 77
- GPS Position 77
- Other Information 78
- Control Settings 79
- Networking 80
- Traceroute 83
- Administration 84
- Admin Users 85
- Restart Web Interface 85
- Time Zone 86
- System Log Configuration 86
- SNMP Configuration 87
- SNMP Edit 87
- Configuration Wizard 88
- Boot Log 90
- System Log 90
- Config Log 91
- HTTP Log 91
- SyncServer Help 92
- NTPD Help 92
- Search NTPD Manual 92
- Logging Off 93
- Time Protocol (RFC 868) 97
- Daytime Protocol (RFC 867) 97
- NTP Message Data 99
- SyncServer S100 100
- NTP Authentication 101
- Public Domain NTP Package 102
- Other NTP Considerations 103
- Basic NTP Configuration 104
- ACTS Interface: Dial-up 111
- ACTS Operation 112
- Version 1 113
- Version 3 114
- Frequently Asked Questions 117
- How-to’s and Tips 121
- Use the quick “How to” guide 123
- Solutions 124
- S100 Specifications 127
- Pin Descriptions 128
- Time Glossary 129
- Customer Assistance 145
- Customer Service 146
- Technical Support 146
- Declaration of Conformity 147
- Class A 148
- Antenna Replacement 149
- Numerics 151
Manuais e produtos relacionados com Hardware Symmetricom S100
Hardware Symmetricom 58502A Manual do Utilizador
(88 páginas)
(88 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais